Fixing Up Structures (Part 3) - Finished For Now

This is how the "auto parts manufacturer" on my GTW line looked a couple of weeks ago before I started to modify it to better suit the 86 foot boxcars that generally get spotted there:

And below, we have a look at the end section after it's been modified

I added piece of vertical pipe - actually a piece of parts sprue - to try to help disguise the seam in the wall. A short section of track is also added to reach the end of the MDF.  Along the way I also clumsily managed to damage some of the fencing in front of the track, so I've cut that section out.  I'll have to make a new piece to replace that.

Track is in and painted, some rust powder along the ties, coarse ground cover, new section of fence, and the track bumper in place.

After I cleaned the rail heads, I lifted the whole structure module back over to it's place on the layout and tested it out with a six-axle engine.  Power to the entire track is evidenced by the headlight operating the locomotive.

I know there's probably not a big visible difference to most of you, but with that offset wall removed we have 3 86 footers spotted at the plant instead of two as before. And fitting the space quite nicely, just as I had hoped.  You'd almost think I knew what I was doing. Almost.

I've omitted putting a gate at the rail entrance.  It should have one, but I'm thinking of actually relocating the whole module some time in the future and making the building and spur longer so it could perhaps take another car or two.  We'll see.

So, that'll be it for 2022.  Thanks for looking in here, I appreciate it. And I wish everybody a Happy New Year.

Fixing Up Structures (Part Two)

I left off last time as this structure was about to make a trip over to the workbench to have the roof cleaned up a little.  Well, that's done, including gluing down the roof vents onto the left hand end of the roof. I also added one more similar vent that I found I had on hand, and a couple of small ones at the other end of the roof.

All set to go back into place on the layout.

Next up for such maintenance is this pretty large industrial building.  This building is just shy of 49 1/2 inches long, and I spot my 86 foot boxcars at it. It will get a little bit more that a dusting though.  See that sort of bump-out at the far end of the building?  I want to take that off so that I can extend the spur track by the extra five or so inches.

If I take that offset out and extend the track, I think I'll be able to spot an extra 86 foot boxcar in there. If I put 3 of the big boxcars in here now, they look kind of like they're "forced" in there. 

This is the section that I want to modify

And after a few minutes of work, the short wall section is removed and lying on the bench on it's way to the parts box in case I ever have a need for such a thing. The depth of the end section of the building will be trimmed a bit and then put back in place. Not sure just yet, but when the track is extended I might need to add or relocate a loading dock door too.

That's as far as I've gotten with this project.  I hope to have it finished up real soon.

In case you somehow missed it, there was a pretty wild truck-train crash in Tennessee this week.  The truck was carrying a 120 foot-long concrete I-beam intended for a nearby overpass project. The two train crew members suffered minor injuries.  Here's the link to video of the collision.

https://www.youtube.com/watch?v=osO5jkxSP_A

And drone video of the aftermath of the crash:

https://www.youtube.com/watch?v=S8TOHUYmbZc

I hope you all have a very Merry Christmas and very Happy Holidays.

Fixing Up Structures

I decided to finally get around to doing a little clean-up and maybe some minor improvements on at least one of the industries on the layout. With the open floor joists above the layout, dirt and dust and stuff does fall from above and land on things.  Over time things do become a bit unsightly.

I could use a bit of a break from weathering freight cars anyway.

I decided to start with an easy, but important one, which is to clean up the Midwest Plastics plant.

The building, track, and fence are all mounted on 1/8th inch MDF.  All I have to do is slide the rail joiners back, and then I can lift the whole thing right out and carry it all over to the workbench.  I expect it will get there in one piece.

Made it to the bench at least!

This is the type of stuff that falls from above onto the building

Vacuum cleaner and a soft brush to clean up

I must have let myself get distracted (which would be typical of me) 3 years ago when I put the buildings together because the rooftop vents (Walther's kit parts) have been just sitting on there loose the whole time. I'll add one or two more and glue them down.

I framed in the overhang on the roof with some I-beam painted with red primer, and added an extra vent on the roof and one on the front near the window. The air unit got some light weathering, a door to the roof was put into one wall and a random piece of piping installed too. There were a couple of marks on one silo, so I painted on a couple of small rusty coloured patches.

Once I get MidWest Plastics back in place on the layout, I'll move on to this backdrop structure, doing much the same thing.

This place was never served by rail. It was meant only to fill in space along the backdrop.  The vents on the roof here haven't been glued in place either.

GNTX RailGon

As GNTX was spotted into the metals recycler spur, I was thinking that it looked a little plain. I cut out a bunch of graffiti decals (I know a lot of people "don't like graffiti", but I figure it's here to stay and I try to be somewhat modern on the layout) and applied them along one side of the gondola.

This will more or less match with another gondola of the same type.

RailGon 297391 in the metal recycler spur.  Some time in the past I had sprayed the gondola with Rail Brown.

Rail Brown was also brush painted on the inside of the gondola

Here's the gondola with the graffiti from a variety of decal sets. I dulled down the decals using the airbrush loaded with the same Rail Brown as I mentioned above.

I decided I would do a bit on the inside as well, so I thought I'd make up a removable floor. I've made removable false bottoms for empty gondolas before, but I still needed one for this car.

Starts with a simple piece of .040 styrene that is cut to size to be able to drop in

Brush painted with 3 or 4 coats of brown craft paint

The top piece here is the new one, with a little bit of fine patio stone sand glued in place.  It was then coloured with some rust powders and a couple of drops of Tamiya's Panel Line liquids in black and brown.

False bottoms dropped into two gondolas, the new one at the top in the photo

And the scrap metal loads that I made previously just drop in right on top of the false bottom pieces.

Changing gears now,.. A few weeks ago,  Brian Smith sent me these following 2 pictures from the vacation trip he took to Europe with his adoring wife Laura.

Brian titled this one Railyard in Rome.

I don't think I've ever posted passenger or commuter photos on here before. This is real nice looking equipment, taken I think in Spain.Note the catenary wire.

PROCOR Pellet Hoppers from Rapido

I'll get to the pellet hoppers in a second, but first I like to point out that I've changed up the header photo for December to one of SWeep 7104 passing under the Gratiot Avenue overpass on the JSSX.

I've been wanting and hoping for years for someone to produce the 4-bay rib-sided plastic pellet covered hoppers that I see at the Sarnia yard so often.  Either the Pullman standard type or the Procor type would be fine with me.  Both kinds would be even better, but I'm not sure that would actually happen.  And to me, the differences appear to be very slight anyway.

This car has had the original PROCOR lettering blanked out and the reporting marks are re-lettered to ICRX

A little more weathering on this one

The PROCOR lettering has been blanked out separately on each panel on this car

But enough of the prototype pictures, all of which I took myself down at C-Yard here in Sarnia by the way.

Rapido has actually come out with really nice models of the Procor-built cars, and I ordered two from the Otter Valley Railway late last Wednesday afternoon.  They arrived at my door Friday.  I bet that if I'd ordered them a couple of hours earlier in the day, Otter Valley would have had them here on Thursday.

I would have liked to get three of them, but with the price point being what it is plus shipping plus HST taxes, I settled for just two. I ordered one with the blue lettering and one with black. Here they are just on the workbench.

Rapido provides spare roof hatches for each car. I guess in case I somehow lose them off the models. There's also an information/history sheet included with the models.  There's no air line piping running on the underside of the models, but that's okay with me because I'd probably accidentally break it off sometime anyway.

The model with the black lettering has two different styles of roof hatches.

Just the round hatches on the roof of this one with the blue lettering

Here they are being shoved into the MidWest Plastics spur on the layout.  I wouldn't normally put new freight cars out on the layout without at least painting the wheels on them, but I did it this time.  I have added the yellow reflective stripes and I sprayed Tamiya Clear Flat over the cars to take down some of that brand new model shine.

Any other weathering is going to have to wait. At 5280 cubic feet and over 62 feet long these make really nice models, and I'm happy to finally have them.